ELASTOPHENE FLAM 25 PDF

ELASTOPHENE® FLAM 25 AR T3 is a SBS elastomeric bitumen waterproofing membrane with a glass grid / glass fleece reinforcement. The topside is protected . ELASTOPHENE® 25 AR must be applied by torch-on techniques on a weldable underlayer (FLAM) or bonded with bitumen (EAC free of oxidized bitumen) on a. ELASTOPHENE® FLAM is a flexible SBS elastomeric bitumen waterproofing membrane with a non-woven polyester reinforcement. Both sides are.

Author: Kazigal Nezshura
Country: India
Language: English (Spanish)
Genre: Politics
Published (Last): 15 October 2013
Pages: 176
PDF File Size: 13.8 Mb
ePub File Size: 7.25 Mb
ISBN: 705-4-93920-581-3
Downloads: 9043
Price: Free* [*Free Regsitration Required]
Uploader: Mazulkree

Click on photo to enlarge.

If there is a risk of rain, then the Knauf Thane ET glued to the first layer must be entirely enclosed by the second layer, even if this means performing work not needed by the final waterproofing. The second bitumous layer is of the same elastophfne as the first.

Soudage du renfort sur platine et dalle. Last drops of the weekend’s heavy rain. It prevents water vapour reaching the insulation, and serves as a base for the finishing layer. Finition autour de la platine.

ELASTOPHENE® 25 AR

The collector is trimmed before applying the outer reinforcement. Before the insulation is laid, the channels carrying the rain water are reinforced: The first layer and the sidewall reinforcement are complete after 4 days.

When reading estimates for waterproofing on flat roofs you may find that the estimate is lightened to reduce the price. Rodolphe Ferracane, e-mail contact AFR-etancheite. Pas une goute n’entre dans la maison. The photos on this page describe the work.

  LEY 17292 PDF

Click on the photos to enlarge them. These are ajusted now but will be fitted later taking into account the future height of the finished surface.

Applying the insulation requires careful attention to the weather forecast and the planning of the work. Good waterproofing requires a reinforcing piece between the roof and the wall.

Fitting the 2nd layer in front of the future rain collector. Creative Commons Attribution – Pas de Modification 3.

For example the first layer could be omitted, and the insulation glued directly to the existing surface. The orientation of elastopheme second layer depends on the way in which flaj third layer will be applied.

Cinq points de Sopracolle par plaque. Creative Commons Attribution – NoDerivs 3. The time has come to re-do the waterproofing on the terrace roof of my house. As with the 1st layer, the joint of the flat roof and the rising walls that surround the roof are a possible source of leaks.

The work specified by this standard is often referred to as Three layers plus insulation, with heated reinforcement. Bitumous glue is applied to the rising side walls. La partie bitume fait approximativement 2. Click tlam figure to enlarge. L’isolation Knauf Thane ET. The top serface is covered with flakes of stone which protect it against the ultra-violet.

  CLAVIS PATRUM GRAECORUM PDF

Une nouvelle étanchéité pour le toit terrasse

On my roof, the rolls of the final layer are positioned north-south, so the second layer must be east-west. The first layer, which provides the waterproofing, is of elastic bitumen, 2.

Removal of remnants of previous waterproofing. Since the new waterproofing and the eladtophene will raise the roof, the rainwater drains must also be raised. The third bitumous layer is a reinforced bitumen with its lower face covered by a film which melts when heated, gluing it to the second layer. The weekend brings heavy rain to test the waterproofing — not a drop gets through to the house.

ELASTOPHENE® FLAM 25 – Soprema

Cutting nord end of a roll of finishing layer. The two layers should be perpendicular to one elasyophene. Before work begins, the existing concrete surface was cleaned with a high pressure bar hose equipped with a rotating jet. Finishing around rain water collector See 2. Heating the outer-reinforcement and the collector. Welding the outer reinforcement onto the collector. Il est bien plus rapide de remplacer les renforts par le flashing: